Acenaphthylene-Based Chromophores for Dye-Sensitized Solar Cells: Synthesis, Spectroscopic Properties, and Theoretical Calculations.

A set of acenaphthylene dyes with arylethynyl π-bridges was tested for dye-sensitized solar cells (DSSCs). Crucial steps for the extension of the conjugated system from the acenaphylene core involved Sonogashira coupling reactions. Phenyl, thiophene, benzotriazole, and thieno-[3,2-b]thiophene moieties were employed to extend the conjugation of the π-bridges. The systems were characterized by cyclic voltammetry and by UV-vis absorption and emission. The spectroscopic characterization showed that the last three bridges resulted in red-shifted absorption and emission spectra relative to the parent phenyl-bridged compound, in accordance with TD-DFT calculations. The phenylethynyl derivative 6a achieved a conversion efficiency of 2.51% with Voc, Jsc, and FF values of 0.365 V, 13.32 mA/cm2, and 0.52, respectively. The efficiency of this compound improved to 3.15% with the addition of CDCA (10 mM), representing the best efficiency result in this study. The overall conversion efficiency of the other aryl derivatives 6b-d proved to be significantly inferior (14-40%) to that of 6a due to a significant decrease of Jsc.

Engineering Metal Halide Perovskite Nanocrystals with BODIPY Dyes for Photosensitization and Photocatalytic Applications.

The sensitization of surface-anchored organic dyes on semiconductor nanocrystals through energy transfer mechanisms has received increasing attention owing to their potential applications in photodynamic therapy, photocatalysis, and photon upconversion. Here, we investigate the sensitization mechanisms through visible-light excitation of two nanohybrids based on CsPbBr3 perovskite nanocrystals (NC) functionalized with borondipyrromethene (BODIPY) dyes, specifically 8-(4-carboxyphenyl)-1,3,5,7-tetramethyl-4,4-difluoro-4-bora-3a,4a-diaza-s-indacene (BDP) and 8-(4-carboxyphenyl)-2,6-diiodo-1,3,5,7-tetramethyl-4,4-difluoro-4-bora-3a,4a-diaza-s-indacene (I2-BDP), named as NC@BDP and NC@I2-BDP, respectively. The ability of I2-BDP dyes to extract hot hole carriers from the perovskite nanocrystals is comprehensively investigated by combining steady-state and time-resolved fluorescence as well as femtosecond transient absorption spectroscopy with spectroelectrochemistry and quantum chemical theoretical calculations, which together provide a complete overview of the phenomena that take place in the nanohybrid. Förster resonance energy transfer (FRET) dominates (82%) the photosensitization of the singlet excited state of BDP in the NC@BDP nanohybrid with a rate constant of 3.8 ± 0.2 × 1010 s-1, while charge transfer (64%) mediated by an ultrafast charge transfer rate constant of 1.00 ± 0.08 × 1012 s-1 from hot states and hole transfer from the band edge is found to be mainly responsible for the photosensitization of the triplet excited state of I2-BDP in the NC@I2-BDP nanohybrid. These findings suggest that the NC@I2-BDP nanohybrid is a unique energy transfer photocatalyst for oxidizing α-terpinene to ascaridole through singlet oxygen formation.

Nickel Oxide Hole Injection Layers for Balanced Charge Injection in Quantum Dot Light-Emitting Diodes.

Quantum dot (QD) light-emitting diodes (QLEDs) are promising for next-generation displays, but suffer from carrier imbalance arising from lower hole injection compared to electron injection. A defect engineering strategy is reported to tackle transport limitations in nickel oxide-based inorganic hole-injection layers (HILs) and find that hole injection is able to enhance in high-performance InP QLEDs using the newly designed material. Through optoelectronic simulations, how the electronic properties of NiOx affect hole injection efficiency into an InP QD layer, finding that efficient hole injection depends on lowering the hole injection barrier and enhancing the acceptor density of NiOx is explored. Li doping and oxygen enriching are identified as effective strategies to control intrinsic and extrinsic defects in NiOx, thereby increasing acceptor density, as evidenced by density functional theory calculations and experimental validation. With fine-tuned inorganic HIL, InP QLEDs exhibit a luminance of 45 200 cd m-2 and an external quantum efficiency of 19.9%, surpassing previous inorganic HIL-based QLEDs. This study provides a path to designing inorganic materials for more efficient and sustainable lighting and display technologies.

Synthesis and characterization of fluorescent poly(α-cyclodextrin)/carbon quantum dots composite for efficient removal and detection of toluene and xylene from aqueous media.

This study reports the synthesis and characterization of a supramolecular composite comprised of carbon dots (CDots) embedded within net-poly[(α-cyclodextrin)-ν-(citric acid)] (α-CD/CA/CDots) for the removal and detection of toluene and xylene from aqueous media. The remarkable stability of CDots within the composite enables the preservation of photoluminescence properties for prolonged storage and extended UV-light irradiation. As demonstrated, following the adsorption of both organic compounds, the composite detected them in the aqueous medium due to a fluorescence quenching mechanism. Spectroscopic analyses reveal that the accessible Stern-Volmer quenching constants for toluene and xylene are KSVa = 15.4 M-1 and KSVa = 10.3 M-1, respectively. As a result, the α-CD/CA/CDots composite were sensitive to the tested volatile organic compounds (LODtoluene = 3.7 mg/L and LODxylene = 4.9 mg/L). Optimal conditions for toluene and xylene adsorption were found, allowing to achieve noticeable adsorption capabilities (qe(toluene) = 68.9 and qe(xylene) = 48.2 mg/g) and removal efficiencies exceeding 70%. Different characterization techniques confirmed the successful synthesis of the composite and elucidated the interaction mechanisms between the adsorbent and the tested compounds. In summary, the multifunctionality demonstrated by the α-CD/CA/CDots composite ranks it as an efficient and promising adsorbent and detection probe for this class of water contaminants.

Tuning Fluorescence and Singlet Oxygen Quantum Yields of Subporphyrazines by Axial Functionalization.

The axial functionalization of Subporphyrazines (SubPzs) with unreported alkoxy groups, carboxy and carboperoxy rests, as well as sulfanyl, aryl and amino groups, forming B-O, B-S, B-C, and B-N bonds, respectively, has been investigated. The studied oxygen nucleophiles include aromatic and sterically demanding aliphatic alcohols, along with carboxylic acids and peracids. In general, direct substitution of the chloro-SubPz by oxygen nucleophiles of diverse nature proceeds smoothly, with yields of the isolated alkoxy and carboxy-substituted SubPzs ranging from 49 to 100 %. Conversely, direct substitution with sulphur, carbon and nitrogen nucleophiles do not afford the corresponding substituted SubPzs. In these cases, a stepwise procedure involving an axial triflate-SubPz intermediate was employed, affording only the phenyl-SubPz in 8 % yield. The major compound under these conditions was the unreported SubPz µ-oxo dimer, presumably arising from substitution of the triflate-SubPz by the in situ generated hydroxy-SubPz. This result indicates a quite low reactivity of the TfO-SubPz intermediate with carbon, sulphur and nitrogen nucleophiles. All SubPzs prepared in this work exhibited fluorescence at 510-515 nm with quantum yields ranging from 0.1 to 0.24. Additionally, all SubPzs generated singlet oxygen, with ΦΔ values ranging from 0.15 to 0.57, which show no apparent correlation with the axial substituents.

Effect of Co Doping on the Physical Properties and Organic Pollutant Photodegradation Efficiency of ZnO Nanoparticles for Environmental Applications.

This paper presents a comprehensive investigation of the synthesis and characterization of Zn1-xCoxO (0 ≤ x ≤ 0.05) nanopowders using a chemical co-precipitation approach. The structural, morphological, and vibrational properties of the resulting ZnO nanostructures were assessed through X-ray diffraction, scanning electronic microscopy, and Raman spectroscopy to examine the influence of cobalt doping. Remarkably, a notable congruence between the experimental results and the density functional theory (DFT) calculations for the Co-doped ZnO system was achieved. Structural analysis revealed well-crystallized hexagonal wurtzite structures across all samples. The SEM images demonstrated the formation of spherical nanoparticles in all the samples. The vibrational properties confirmed the formation of a hexagonal wurtzite structure, with an additional Raman peak corresponding to the F2g vibrational mode characteristic of the secondary phase of ZnCo2O4 observed at a 5% cobalt doping concentration. Furthermore, a theoretical examination of cobalt doping's impact on the elastic properties of ZnO demonstrated enhanced mechanical behavior, which improves stability, recyclability, and photocatalytic activity. The photocatalytic study of the synthesized compositions for methylene blue (MB) dye degradation over 100 min of UV light irradiation demonstrated that Co doping significantly improves photocatalytic degradation. The material's prolonged lifetime, reduced rate of photogenerated charge carrier recombination, and increased surface area were identified as pivotal factors accelerating the degradation process. Notably, the photocatalyst with a Zn0.99Co0.01O composition exhibited exceptional efficiency compared to that reported in the literature. It demonstrated high removal activity, achieving an efficiency of about 97% in a shorter degradation time. This study underscores the structural and photocatalytic advancements in the ZnO system, particularly at lower cobalt doping concentrations (1%). The developed photocatalyst exhibits promise for environmental applications owing to its superior photocatalytic performance.

Dicarboxylic Acid-Assisted Surface Oxide Removal and Passivation of Indium Antimonide Colloidal Quantum Dots for Short-Wave Infrared Photodetectors.

Heavy-metal-free III-V colloidal quantum dots (CQDs) are promising materials for solution-processed short-wave infrared (SWIR) photodetectors. Recent progress in the synthesis of indium antimonide (InSb) CQDs with sizes smaller than the Bohr exciton radius enables quantum-size effect tuning of the band gap. However, it has been challenging to achieve uniform InSb CQDs with band gaps below 0.9 eV, as well as to control the surface chemistry of these large-diameter CQDs. This has, to date, limited the development of InSb CQD photodetectors that are sensitive to ≥ ${\ge }$ 1400 nm light. Here we adopt solvent engineering to facilitate a diffusion-limited growth regime, leading to uniform CQDs with a band gap of 0.89 eV. We then develop a CQD surface reconstruction strategy that employs a dicarboxylic acid to selectively remove the native In/Sb oxides, and enables a carboxylate-halide co-passivation with the subsequent halide ligand exchange. We find that this strategy reduces trap density by half compared to controls, and enables electronic coupling among CQDs. Photodetectors made using the tailored CQDs achieve an external quantum efficiency of 25 % at 1400 nm, the highest among III-V CQD photodetectors in this spectral region.

Arresting Ion Migration from the ETL Increases Stability in Infrared Light Detectors Based on III-V Colloidal Quantum Dots.

III-V colloidal quantum dots (CQDs) are of interest in infrared photodetection, and recent developments in CQDs synthesis and surface engineering have improved performance. Here this work investigates photodetector stability, finding that the diffusion of zinc ions from charge transport layers (CTLs) into the CQDs active layer increases trap density therein, leading to rapid and irreversible performance loss during operation. In an effort to prevent this, this work introduces organic blocking layers between the CQDs and ZnO layers; but these negatively impact device performance. The device is then, allowing to use a C60:BCP as top electron-transport layer (ETL) for good morphology and process compatibility, and selecting NiOX as the bottom hole-transport layer (HTL). The first round of NiOX -based devices show efficient light response but suffer from high leakage current and a low open-circuit voltage (Voc) due to pinholes. This work introduces poly[bis(4-phenyl) (2,4,6-trimethylphenyl)amine] (PTAA) with NiOX NC to form a hybrid HTL, an addition that reduces pinhole formation, interfacial trap density, and bimolecular recombination, enhancing carrier harvesting. The photodetectors achieve 53% external quantum efficiency (EQE) at 970 nm at 1 V applied bias, and they maintain 95% of initial performance after 19 h of continuous illuminated operation. The photodetectors retain over 80% of performance after 80 days of shelf storage.

Interaction between a water-soluble anionic porphyrin and human serum albumin unexpectedly stimulates the aggregation of the photosensitizer at the surface of the albumin.

The 5,10,15,20-tetrakis(2,6-difluoro-3-sulfophenyl)porphyrin (TDFPPS4) was reported as a potential photosensitizer for photodynamic therapy. The capacity of the photosensitizers to be carried in the human bloodstream is predominantly determined by its extension of binding, binding location, and binding mechanism to human serum albumin (HSA), influencing its biodistribution and ultimately its photodynamic therapy efficacy in vivo. Thus, the present work reports a biophysical characterization on the interaction between the anionic porphyrin TDFPPS4 and HSA by UV-visible absorption, circular dichroism, steady-state, time-resolved, and synchronous fluorescence techniques under physiological conditions, combined with molecular docking calculations and molecular dynamics simulations. The interaction HSA:TDFPPS4 is spontaneous (ΔG° < 0), strong, and enthalpically driven (ΔH° = -70.1 ± 3.3 kJ mol-1) into subdomain IIA (site I). Curiously, despite the porphyrin binding into an internal pocket, about 50 % of TDFPPS4 structure is still accessible to the solvent, making aggregation in the bloodstream possible. In silico calculations were reinforced by spectroscopic data indicating porphyrin aggregation between bound and unbound porphyrins. This results in an adverse scenario for anionic porphyrins to achieve their therapeutical potential as photosensitizers and control of effective dosages. Finally, a trend of anionic porphyrins to have a combination of quenching mechanisms (static and dynamic) was noticed.

Halide-Driven Synthetic Control of InSb Colloidal Quantum Dots Enables Short-Wave Infrared Photodetectors.

In the III-V family of colloidal quantum dot (CQD) semiconductors, InSb promises access to a wider range of infrared wavelengths compared to many light-sensing material candidates. However, achieving the necessary size, size-dispersity, and optical properties has been challenging. Here the synthetic challenges associated with InSb CQDs are investigated and it is found that uncontrolled reduction of the antimony precursor hampers the controlled growth of CQDs. To overcome this, a synthetic strategy that combines nonpyrophoric precursors with zinc halide additives is developed. The experimental and computational studies show that zinc halide additives decelerate the reduction of the antimony precursor, facilitating the growth of more uniformly sized CQDs. It is also found that the halide choice provides additional control over the strength of this effect. The resultant CQDs exhibit well-defined excitonic transitions in spectral range of 1.26-0.98 eV, along with strong photoluminescence. By implementing a postsynthesis ligand exchange, colloidally stable inks enabling the fabrication of high-quality CQD films are achieved. The first demonstration of InSb CQD photodetectors is presented reaching 75% external quantum efficiency (QE) at 1200 nm, to the knowledge the highest short-wave infrared (SWIR) QE reported among heavy-metal-free infrared CQD-based devices.

Seminal Vesicle Calculi as a Cause of Hematospermia and Ejaculatory Pain: A Case Report.

Seminal vesicle calculi are a rare entity that may present with hematospermia, painful ejaculation, or urinary complaints. We present a case of a 40-year-oldmale with complaints of hematospermia, ejaculatory pain, and perineal discomfort in the last five years. A 7 mm left seminal vesicle calculi were diagnosed by magnetic resonance imaging (MRI), and a laparoscopic robot-assisted vesiculectomy was performed. All the complaints improved completely after treatment. Seminal vesicle lithiasis should be kept in mind when evaluating patients with hematospermia and ejaculatory pain. Transrectal ultrasound (TRUS) and magnetic resonance imaging are the best radiology techniques to diagnose this kind of lithiasis. Different surgical treatments can be used to treat these calculi, depending on the size and location of the calculi and the surgical experience of the surgeon.

Sequential Co-Passivation in InAs Colloidal Quantum Dot Solids Enables Efficient Near-Infrared Photodetectors.

III-V colloidal quantum dots (CQDs) are promising materials for optoelectronic applications, for they avoid heavy metals while achieving absorption spanning the visible to the infrared (IR). However, the covalent nature of III-V CQDs requires the development of new passivation strategies to fabricate conductive CQD solids for optoelectronics: this work shows herein that ligand exchanges, previously developed in II-VI and IV-VI quantum dots and employing a single ligand, do not fully passivate CQDs, and that this curtails device efficiency. Guided by density functional theory (DFT) simulations, this work develops a co-passivation strategy to fabricate indium arsenide CQD photodetectors, an approach that employs the combination of X-type methyl ammonium acetate (MaAc) and Z-type ligands InBr3 . This approach maintains charge carrier mobility and improves passivation, seen in a 25% decrease in Stokes shift, a fourfold reduction in the rate of first-exciton absorption linewidth broadening over time-under-stress, and leads to a doubling in photoluminescence (PL) lifetime. The resulting devices show 37% external quantum efficiency (EQE) at 950 nm, the highest value reported for InAs CQD photodetectors.

Control over Charge Carrier Mobility in the Hole Transport Layer Enables Fast Colloidal Quantum Dot Infrared Photodetectors.

Solution-processed colloidal quantum dots (CQDs) are promising materials for photodetectors operating in the short-wavelength infrared region (SWIR). Devices typically rely on CQD-based hole transport layers (HTL), such as CQDs treated using 1,2-ethanedithiol. Herein, we find that these HTL materials exhibit low carrier mobility, limiting the photodiode response speed. We develop instead inverted (p-i-n) SWIR photodetectors operating at 1370 nm, employing NiOx as the HTL, ultimately enabling 4× shorter fall times in photodiodes (∼800 ns for EDT and ∼200 ns for NiOx). Optoelectronic simulations reveal that the high carrier mobility of NiOx enhances the electric field in the active layer, decreasing the overall transport time and increasing photodetector response time.

Novel Oxygen- and Curcumin-Laden Ionic Liquid@Silica Nanocapsules for Enhanced Antimicrobial Photodynamic Therapy.

The efficiency of photodynamic therapy is often limited by the scarcity of oxygen at the target site. To address this problem, this work proposes the development of a new nanosystem for antimicrobial photodynamic therapy applications (aPDT) where the natural-origin photosensitizer curcumin (CUR) is immersed in an oxygen-rich environment. Inspired by the perfluorocarbon-based photosensitizer/O2 nanocarriers reported in the literature, we developed a new type of silica nanocapsule containing curcumin dissolved in three hydrophobic ionic liquids (ILs) with high oxygen dissolving capacities. The nanocapsules (CUR-IL@ncSi), prepared by an original oil-in-water microemulsion/sol-gel method, had a high IL content and exhibited clear capacities to dissolve and release significant amounts of oxygen, as demonstrated by deoxygenation/oxygenation studies. The ability of CUR-IL solutions and of CUR-IL@ncSi to generate singlet oxygen (1O2) upon irradiation was confirmed by the detection of 1O2 phosphorescence at 1275 nm. Furthermore, the enhanced capacities of oxygenated CUR-IL@ncSi suspensions to generate 1O2 upon irradiation with blue light were confirmed by an indirect spectrophotometric method. Finally, preliminary microbiological tests using CUR-IL@ncSi incorporated into gelatin films showed the occurrence of antimicrobial effects due to photodynamic inactivation, with their relative efficiencies depending on the specific IL in which curcumin was dissolved. Considering these results, CUR-IL@ncSi has the potential to be used in the future to develop biomedical products with enhanced oxygenation and aPDT capacities.

Synthesis of Highly Luminescent Silica-Coated Upconversion Nanoparticles from Lanthanide Oxides or Nitrates Using Co-Precipitation and Sol-Gel Methods.

Upconversion nanoparticles (UCNPs) are under consideration for their use as bioimaging probes with enhanced optical performance for real time follow-up under non-invasive conditions. Photostable and core-shell NaYF4:Yb3+, Er3+-SiO2 UCNPs obtained by a novel and simple co-precipitation method from lanthanide nitrates or oxides were herein synthesized for the first time. The sol-gel Stöber method followed by oven or supercritical gel drying was used to confer biocompatible surface properties to UCNPs by the formation of an ultrathin silica coating. Upconversion (UC) spectra were studied to evaluate the fluorescence of UCNPs upon red/near infrared (NIR) irradiation. ζ-potential measurements, TEM analyses, XRD patterns and long-term physicochemical stability were also assessed and confirmed that the UCNPs co-precipitation synthesis is a shape- and phase-controlling approach. The bio- and hemocompatibility of the UCNPs formulation with the highest fluorescence intensity was evaluated with murine fibroblasts and human blood, respectively, and provided excellent results that endorse the efficacy of the silica gel coating. The herein synthesized UCNPs can be regarded as efficient fluorescent probes for bioimaging purposes with the high luminescence, physicochemical stability and biocompatibility required for biomedical applications.

Bioimaging of Lysosomes with a BODIPY pH-Dependent Fluorescent Probe.

Fluorescence-based probes represent a powerful tool for noninvasive imaging of living systems in real time and with a high temporal and spatial resolution. Amongst several known fluorophores, 3-difluoroborodipyrromethene (BODIPY) derivatives have become a cornerstone for innovative fluorescent labelling applications, mainly due to their advantageous features including their facile synthesis, structural versatility and exceptional photophysical properties. In this context, we report a BODIPY-based fluorescent probe for imaging of lysosomes in living cells. The BODIPY derivative displayed a remarkable fluorescence enhancement at low pH values with a pKa* of 3.1. In vitro studies by confocal microscopy in HeLa cells demonstrated that the compound was able to permeate cell membrane and selectively label lysosome whilst remaining innocuous to the cell culture at the maximum concentration tested. Herein, the BODIPY derivative holds the promise of investigating lysosomal dynamics and function in living cells through fluorescence imaging.

Dipole Engineering through the Orientation of Interface Molecules for Efficient InP Quantum Dot Light-Emitting Diodes.

InP-based quantum dot (QD) light-emitting diodes (QLEDs) provide a heavy-metal-free route to size-tuned LEDs having high efficiency. The stability of QLEDs may be enhanced by replacing organic hole-injection layers (HILs) with inorganic layers. However, inorganic HILs reported to date suffer from inefficient hole injection, the result of their shallow work functions. Here, we investigate the tuning of the work function of nickel oxide (NiOx) HILs using self-assembled molecules (SAMs). Density functional theory simulations and near-edge X-ray absorption fine structure put a particular focus onto the molecular orientation of the SAMs in tuning the work function of the NiOx HIL. We find that orientation plays an even stronger role than does the underlying molecular dipole itself: SAMs having the strongest electron-withdrawing nitro group (NO2), despite having a high intrinsic dipole, show limited work function tuning, something we assign to their orientation parallel to the NiOx surface. We further find that the NO2 group─which delocalizes electrons over the molecule by resonance─induces a deep lowest unoccupied molecular orbital level that accepts electrons from QDs, producing luminescence quenching. In contrast, SAMs containing a trifluoromethyl group exhibit an angled orientation relative to the NiOx surface, better activating hole injection into the active layer without inducing luminescence quenching. We report an external quantum efficiency (EQE) of 18.8%─the highest EQE among inorganic HIL-based QLEDs (including Cd-based QDs)─in InP QLEDs employing inorganic HILs.

Magnetic resonance imaging target fusion biopsy vs. transrectal ultrasound-guided biopsy - A comparative study of ISUP score upgrading risk in the final radical prostatectomy specimen.

OBJECTIVES: The aim of this study was to com-pare the risk of International Society of Urological Pathology (ISUP) score upgrading between magnetic resonance imaging targeted fusion biopsy (MRI-TB) and tran-srectal ultrasound-guided biopsy (TRUS-B) in the final radical prostatectomy (RP) specimen pathological report. MATERIALS AND METHODS: This retrospective single center study included 51 patients with prostate cancer (PCa) diagnosed with MRI-TB and 83 patients diagnosed with TRUS-B between October/2019 and July/2021. We compared the rates of ISUP score upgrading between both groups after robotic-assisted radi-cal prostatectomy (RARP) and the specific transition of each ISUP score based on biopsy modality. The rate of ISUP score concordance and downgrading were also assessed. To define the intra and interobserver concordance for each ISUP score in biopsy and RP specimen for each biopsy modality, the Cohen's Kappa coefficient was calculated. ISUP scores and biopsy modal-ity were selected for multivariate analysis and a logistic regres-sion model was built to provide independent risk factors of ISUP score upgrading. RESULTS: The difference of the rate of upgrading between MRI-TB group and TRUS-B group was statistically significant (p = 0.007) with 42.2% of patients of TRUS-B group experiencing an upgrade in their ISUP score while only 19.6% in MRI-TB group. Concordance and downgrading rates did not statistically differ between the two groups. Strength of concordance using Cohen's Kappa coefficient was fair in both groups but higher in MRI-TB group (TRUS-B group k = 0.230; p < 0.001; concordance: 47%vs. MRI/TB group k = 0.438; p < 0.001; concordance: 62.7%). Biopsy modality and ISUP 1 on biopsy were independent predic-tors of ISUP upgrading after RP. CONCLUSIONS: MRI-TB is highly accurate with lower risk of PCa upgrading after RP than TRUS-B. Patients with ISUP 1 on biopsy have greater susceptibility to upgrading their ISUP score.

Electron-Transport Layers Employing Strongly Bound Ligands Enhance Stability in Colloidal Quantum Dot Infrared Photodetectors.

Solution-processed photodetectors based on colloidal quantum dots (CQDs) are promising candidates for short-wavelength infrared light sensing applications. Present-day CQD photodetectors employ a CQD active layer sandwiched between carrier-transport layers in which the electron-transport layer (ETL) is composed of metal oxides. Herein, a new class of ETLs is developed using n-type CQDs, finding that these benefit from quantum-size effect tuning of the band energies, as well as from surface ligand engineering. Photodetectors operating at 1450 nm are demonstrated using CQDs with tailored functionalities for each of the transport layers and the active layer. By optimizing the band alignment between the ETL and the active layer, CQD photodetectors that combine a low dark current of ≈1 × 10-3 mA cm-2 with a high external quantum efficiency of ≈66% at 1 V are reported, outperforming prior reports of CQD photodetectors operating at >1400 nm that rely on metal oxides as ETLs. It is shown that stable CQD photodetectors rely on well-passivated CQDs: for ETL CQDs, a strongly bound organic ligand trans-4-(trifluoromethyl)cinnamic acid (TFCA) provides improved passivation compared to the weakly bound inorganic ligand tetrabutylammonium iodide (TBAI). TFCA suppresses bias-induced ion migration inside the ETL and improves the operating stability of photodetectors by 50× compared to TBAI.

Quantum-Size-Effect Tuning Enables Narrowband IR Photodetection with Low Sunlight Interference.

Infrared photodetection enables depth imaging techniques such as structured light and time-of-flight. Traditional photodetectors rely on silicon (Si); however, the bandgap of Si limits photodetection to wavelengths shorter than 1100 nm. Photodetector operation centered at 1370 nm benefits from lower sunlight interference due to atmospheric absorption. Here, we report 1370 nm-operating colloidal quantum dot (CQD) photodetectors and evaluate their outdoor performance. We develop a surface-ligand engineering strategy to tune the electronic properties of each CQD layer and fabricate photodetectors in an inverted (PIN) architecture. The strategy enables photodetectors with an external quantum efficiency of 75% and a low dark current (1 µA/cm2). Outdoor testing demonstrates that CQD-based photodetectors combined with a 10 nm-line width bandpass filter centered at 1370 nm achieve over 2 orders of magnitude (140× at incident intensity 1 µW/cm2) higher signal-to-background ratio than do Si-based photodetectors that use an analogous bandpass filter centered at 905 nm.